AirPods Blinking White – Why and How to Fix?

Are your AirPods blinking white but not connecting? Don’t worry!

If your AirPods show a flashing white light, they are in pairing mode and searching for an Apple device to pair with but are unable to do so.

Don’t be concerned! If you see a blinking white light on your AirPods, here is a comprehensive guide to all the potential causes and solutions.

Why Do My AirPods Keep Blinking White?

The status light on your AirPods case typically blinks white when your AirPods are ready to enter the pairing mode.

However, there may be other issues because of which your AirPods keep blinking white, such as a connection or pairing error. Many reasons may cause this, such as using out-of-date firmware or disabled Bluetooth connection.

No matter the cause, we guarantee to provide a workable solution and assist you in resolving the issue. 

How to Stop My AirPods from Blinking White?

Here’s how to fix Airpods flashing white issue:

Recharge Your AirPods

A low battery might prevent your AirPods from staying connected to your phone or computer. Hence, if your AirPods’ battery is dead, try charging them first.

The AirPods case’s status light shows up in two colors for comparison. If the charging case’s light is a green light, your AirPods are completely charged. If the case or AirPods are blinking amber, they need recharging.

Clean the AirPods and Case Thoroughly

Blocked flow of electricity between the AirPods’ charging pin and the case’s charging pin is one common reason for pairing failure. Dirt and filth on the AirPods or the case can have the same effect.

It would help if you cleaned your AirPods to rule out the possibility that they have dirt or earwax, which could cause them to flash white.

Follow the steps below to clean your AirPods:

1. Prepare 70% isopropyl alcohol and dampen a cloth using it.
2. Clean your AirPods and case with this microfiber cloth, avoiding the sound grill and other apertures.
3. Use an alcoholic-soaked Q-tip to wipe off the audio grill and the charger ports inside the case.

Turn Bluetooth On/Off

Turning the Bluetooth on and off will reset the pairing process of your AirPods, which might bypass the underlying issue preventing a successful connection.

Follow these steps for iOS users:

1. Locate the Bluetooth section of your device’s settings.
2. Now, press the corresponding button to enable or disable Bluetooth.

Follow these steps for Android users:

1. Navigate to your device’s Connections menu.
2. Tap the trigger to turn Bluetooth on or off.

Connect AirPods Individually

Some AirPods users claim that they could resolve the white light flashing issue by pairing each AirPod separately. As such, you must:

1. Insert one AirPod into the case.
2. Lift the case lid and lay it down very close to your gadget. Now, your device should connect with the AirPods.
3. Remove the AirPod that is now connected and replace it with the other. Go back to Step 2 and do it again.

Update Your AirPods

Frequently, issues like the one you’re having with your AirPods get addressed with software upgrades. Furthermore, AirPod upgrades maintain the earbuds’ compatibility with newer smartphones.

To see whether an update is available for your AirPods, you can:

1. Get into your device’s Bluetooth options.
2. Select the AirPods in the menu of paired gadgets and tap the ‘i’ button. The icon will show the firmware version of the AirPods.

Restart Your Device

Restarting your device resets the settings, which can solve most problems that may prevent your AirPods from connecting properly. First, follow these steps to force restart your device:

1. Hold down the power button unless a screen appears.
2. To do this on an iPhone, press the volume down and power buttons simultaneously.
3. Click Restart device. On Android, this function is represented by a button, while on iOS devices, it is a simple power slider.
4. Do not log in until the device has restarted.

Keep Your Devices’ Software Updated

Your gadgets, including AirPods, will perform better after receiving the latest updates. That’s because software updates are essential for your devices’ continued operation, efficiency, and connection stability (such as Bluetooth). Therefore, consider all the devices that you use with your AirPods. “

Follow these steps to upgrade your gadgets: 

Android

1. Proceed to the device’s Settings.
2. Locate the System Updates menu and click it.
3. Select the Check for Updates tab from the menu.
4. If an upgrade is available, you can obtain the latest files by downloading and installing them. 

iOS

1. Proceed to the General tab in Settings.
2. Head over to Software Update.
3. Accessing this page will reveal the iOS version installed on your gadget and whether or not an upgrade is available.
4. If there’s an upgrade available, click the “Install Update” button to proceed with the upgrade.

macOS

1. Select System Preferences from the Apple menu.
2. Go to Software Updates.
3. If an update is available, you can get it on your Mac by clicking the Update Now button.

Reset Your Network

You can do a “network restore” if you want to delete all Bluetooth and WiFi networks from your device. In addition, it eliminates any possible disruption from other cellular connections by forcing your smartphone and AirPods to begin the pairing process again.

Note – Doing so will log you out of the current WiFi network and need re-authentication.

To reboot your system, you must:

Android

1. Go to your device’s settings
2. Search ‘reset network settings.’
3. Then, choose the option to “Reset Settings.”

iOS

1. Go to the General Menu in your Device’s settings.
2. Now click Reset Network Settings.

macOS

1. Unfortunately, resetting your whole network on a Mac is impossible. You can, however:
2. Select System Preferences from the Apple menu.
3. Press Network.
4. Pick among your available gadgets (including WiFi and other networked gadgets). To remove a device from the list, select it and then click the minus (-) sign.
5. If a confirmation window appears, choose Yes; repeat this process until all warnings have vanished.
6. Now, click apply.

Check Your Devices and Reset Them as Required

You can resolve many problems by disconnecting and connecting all devices to their original settings. It will require each device’s software to reset, which should address any issues with your AirPods.

Resetting AirPods

The following is the procedure to reset your AirPods:

1. Place both the AirPods in the AirPods case and make sure you tightly fasten the lid. Now, wait for a while.
2. Then, open up your device’s Bluetooth options and look for a little info button next to your AirPods.
3. A pull-down menu will display. Click “Forget Device” and confirm. By doing so, your AirPods will get deactivated across all of your Apple devices.
4. Now, open the AirPods case and hold the back-mounted setup button for around 15 seconds until the amber light becomes white.
5. Leave the case’s lid open and put it beside your gadget. Your AirPods should be able to pair successfully now. 

Resetting iPad and iPhone

To factory reset an iPad or iPhone, one must:

1. Go over to the General Tab in the phone settings.
2. Choose “Transfer or Reset iPhone/iPad” from the menu.
3. Click “Erase All Content and Settings” and insert your password.

Resetting Android

Resetting an Android device requires the following steps:

1. Choose the Backup and Reset option from your device’s settings.
2. Choose ‘Factory data reset’
3. Now click the “Erase Everything” button.

Verify the Authenticity of Your AirPods

If the steps above don’t help, your AirPods may be fake. Due to their lower-quality construction, counterfeit AirPods are more prone to malfunction or breakage.

Using the AirPods’ serial number is an easy method to verify their authenticity. Methods for determining the AirPods’ unique identifier are as follows:

Using AirPods Case

You can find the serial number inside the lid of the original AirPods or AirPods Pro carrying case.

Using AirPods Max

You won’t find the AirPods Max serial number on the casing, but rather behind the left ear pad.

Using Bluetooth Settings

Select the ‘More Info’ option in the list of connected devices on your iOS device to get further details about each item. In addition, there is where you can locate the serial number.

Apple’s Original Packaging

You will find the serial number for your AirPods above the label on the back of the package if you have saved it.

Once you have the serial number, you can verify your AppleCare coverage by visiting the AppleCare Coverage Check website. Then, submit the number seen on your serial number entry. Finally, a page should display the earbuds’ information if the AirPods are real.

Apple has included an AirPods reliability check in the latest iOS 16 version. 

If Still Nothing Works, Visit an Apple Service Center

If you’ve attempted all the above methods and your AirPods still won’t pair, you should take your device to an Apple Service Center. There, trained technicians will examine your AirPods and will either be able to repair them or provide you with a replacement pair.

Note – If you are an AppleCare+ customer, then you won’t have to pay for this service. However, you’ll have to bear the expenses if you’re not.

Final Words

This guide has compiled a list of all the solutions to white flashing lights on AirPods. When you are fixing this problem, follow all the instructions given in the method described in this article.

If you continue to see the AirPods case flashing white, this guide will surely fix them. However, suppose none of these solutions prove successful. In that case, it is important to seek a professional’s assistance to resolve the issue.

We hope that your Apple AirPods are now securely lodged in your ears and that you can resume listening to your music. Plus, we hope you are now aware of how to proceed if you face this challenge again!

This was a complete guide on AirPods flashing white light.